Menu
Wood Finishes Specifications
EXTERIOR/INTERIOR WOOD VARNISH GLOSS
- A general purpose interior/exterior solvent based varnish for all wood surfaces.
- For use on new and previously varnished interior or exterior wood surfaces.
- Type: A Long Oil Altyd
- Appearance: Gloss
- Colour: Clear, Dark Oak, Light Oak, Teak and Mahogany
- Solids: 45% by mass
- Density: 0.82 – 0.86.
- Viscosity at 25°ͨ: 65-70Kµ
- Specific Gravity: 0.90-0.91
- Flash Point: @ 34°ͨ
- Mixing: Stir well before use.
- Method: Brush, Rollers not recommended. Conventional Spray.
- Thinning: Mineral Turpentine
- Clean-up: Mineral Turpentine
- Spreading rate: 10-12m²/l depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8°ͨ
- Drying Time: Touch dry 4 hours. Hard dry 18 hour at 25 degrees.
- Recoating Time:18 hours
- Requirements: 2 Coats
New surface must be sound, clean and dry(moisture content below 15%) before painting.
- Sand to a smooth surface in the direction of the wood fiber.
- Remove all dust.
- Thin first coat with 10% Mineral Turpentine.
- Sand slightly with fine sandpaper or fine steel wool in between coats.
- Apply 2nd coat and 3rd unthinned.
- To prevent ingress of moisture the end grain must be coated.
Redecoration
- For surfaces in poor condition: Strip down and treat as new work.
- Surfaces in good condition must be slightly sanded, dusted and then treated as new work.
- For maximum protection on exterior wood 3 coats of varnish is advisable.
- Keep container properly sealed after use.
- Keep away from direct sunlight, heat and severe cold
- 1 litres, 5 litres and 20 litres
- Detailed Safety information: Refers to the material safety data sheet for this product.
- Not to be used as a wood floor coating.
- Do not apply on wet or damp timber.
- Do not paint in wet or cold weather. (Minimum 5°ͨ)
- Drying times will be extended during wet or cold weather conditions
- To prevent ingress of moisture the end grain must be coated.
EXTERIOR/INTERIOR WOOD VARNISH MATT
- A general purpose interior/exterior solvent based varnish for all wood surfaces.
- For use on new and previously varnished interior or exterior wood surfaces.
- Excellent water resistance.
- Excellent exterior durability and very UV resistance.
- Durable wood varnish for all surfaces.
- Type: A Long Oil Altyd
- Appearance: Matt
- Colour: Clear, Dark Oak, Light Oak, Teak and Mahogany
- Solids: 45% by mass
- Density: 0.82 – 0.86.
- Viscosity at 25°ͨ: 65-70Kµ
- Specific Gravity: 0.90-0.91
- Flash Point: @ 34°ͨ
- Mixing: Stir well before use.
- Method: Brush, Rollers not recommended. Conventional Spray.
- Thinning: Mineral Turpentine
- Clean-up: Mineral Turpentine
- Spreading rate: 10-12m²/l depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8℃
- Drying Time: Touch dry 4 hours. Hard dry 18 hour at 25 degrees.
- Recoating Time:18 hours
- Requirements: 2 Coats
- Keep container properly sealed after use.
- Keep away from direct sunlight, heat and severe cold
- 1 litres, 5 litres and 20 litres
- Detailed Safety information: Refers to the material safety data sheet for this product.
- Not to be used as a wood floor coating.
- Do not apply on wet or damp timber.
- Do not paint in wet or cold weather. (Minimum 5℃)
- Drying times will be extended during wet or cold weather conditions
- To prevent ingress of moisture the end grain must be coated.
EXTERIOR WOOD SEALER
- A high quality long life deep penetrating solvent based exterior wood sealer for hard and soft woods.
- Sealer for exterior wood where good abrasion is required.
- Used extensively as decking sealer for doors, windows and frames, gates, fences, garage doors, garden furniture, pergolas etc.
- Excellent water resistance.
- Very tough and hardwearing.
- No peeling and cracking as it penetrates into the wood.
- Excellent exterior durability and very UV resistant.
- Very good protection.
- Anti-Microbial Additives.
- Type: A single component, long oil alkyd based wood sealer with UV Absorbers and Anti-Microbial Additives.
- Appearance: Semi-Gloss.
- Colors: Clear, Mahogany and Meranti.
- Solids: 25% by mass.
- Density: .82-.86.
- Specific Gravity: 0.82 – 0.86.
- Viscosity at 25ºC: 18-20 Seconds FC 4.
- Flash Point: Flammable at 34ºC.
- Mixing: Stir well before use.
- Method: Brush.
- Thinning: Mineral Turpentine.
- Clean up: Mineral Turpentine.
- Spreading rate: 2.5 m ²/l for the first coat and 7m²/l for the second coat depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8º C
- Drying time: Touch dry 6 hours. Hard dry 12 hours at 25 degrees.
- Recoating time: 12 hours.
- Requirements: 2 coats.
- New Surfaces must be sound, clean and dry (moisture content below 15%) before painting.
- Sand to a smooth surface in the direction of the wood fiber.
- Remove all dust.
- Thin first coat with 10% Mineral Turpentine.
- Sand slightly with fine sandpaper or fine steel wool.
- Apply 2nd coast unthinned.
- Ensure that the wood is sealed all round.
- Redecoration.
- For surfaces in poor condition: Strip down and treat as new work.
- Surfaces in good condition must be slightly sanded down, dusted and then treated as new work.
- Wood which has been preserved or oiled before, must be dried out completely and then wiped with Mineral Turpentine. Ensure the surface is totally dried out before applying Versus Vesawood Sealer.
- Keep containers properly sealed.
- Store away from direct heat, sun and severe cold.
- 1 Liter, 5 Litres, 20 Litres, 200 Litres.
- Detailed safety information: refers to the material safety data sheet for this product.
- Not suitable on sealed or varnished surfaces.
- Do not apply on wet or damp surfaces.
- Do not paint in wet or cold weather. (Minimum 5ºC.)
- Drying times will be extended during wet or cold weather conditions.
WOOD PRESERVATIVE
- A single component, long oil Alkyd linseed oil based wood protector.
- A general purpose interior/exterior wood protector used extensively on doors, window frames, gates, fences, pergolas and garage doors.
- Excellent water resistance.
- Very tough and hardwearing.
- Does not form a film which can crack or peel.
- Excellent exterior durability and very UV resistant.
- Very good protection.
- Easy to maintain.
- Type: Long oil Alkyd/linseed oil.
- Appearance: Semi – gloss.
- Colors: Clear. Mahogany and Ebony.
- Solids: 45% by mass.
- Specific Gravity: 0.90 – 0.91.
- Viscosity at 25ºC: 95-70 Kµ.
- Flash Point: 34ºc.
- Mixing: Stir well before use.
- Method: Brush.
- Thinning: Mineral Turpentine.
- Clean up: Mineral Turpentine.
- Spreading rate: 10-12 m ²/l depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8º C
- Drying time: Touch dry 4 hours. Hard dry 18 hours at 25 degrees.
- Recoating time: 18 hours.
- Requirements: 2 coats.
- New Surfaces must be sound, clean and dry (moisture content below 15%) before painting.
- Sand to a smooth surface in the direction of the wood fiber.
- Remove all dust.
- Thin first coat with 10% Mineral Turpentine.
- Sand slightly with fine sandpaper or fine steel wool.
- Apply 2nd coat unthinned.
- Ensure that the wood is sealed all round.
- Redecoration.
- For surfaces in poor condition: Strip down and treat as new work.
- Surfaces in good condition must be slightly sanded down, dusted and then treated as new work.
- Wood which has been preserved or oiled before, must be dried out completely and then wiped with Mineral Turpentine. Ensure the surface is totally dried out before applying Versus Vesawood Sealer.
- Keep containers properly sealed.
- Store away from direct heat, sun and severe cold.
- 5 Litres and 20 Litres.
- Detailed safety information: refers to the material safety data sheet for this product.
- Not suitable on sealed or varnished timber.
- Do not paint in wet, damp or cold weather. (Minimum 5ºC.)
- Drying times will be extended during wet or cold weather conditions.
- To prevent ingress of moisture the end grain must be coated.
PINK WOOD PRIMER
- A solvent based penetrating wood primer for interior and exterior surfaces.
- A general purpose primer for wood
- Economical and easy to apply.
- Good adhesion.
- Very good protection.
- Type: Alkyd.
- Appearance: Matt/low sheen.
- Colors: White and Pink.
- Solids: 63-64% by mass.
- Specific Gravity: 1.35 – 1.4.
- Viscosity (Sheen Cup): 30 -35 Secs.
- DFT/coat: Min 30µm Max 35µm.
- Flash Point: 35ºC.
- Mixing: Stir well before use.
- Method: Short nap mohair roller or brush.
- Thinning: Mineral Turpentine.
- Clean up: Mineral Turpentine.
- Spreading rate: 8 – 10m ²/l depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8º C
- Drying time: Touch dry 3 – 4 hours. Hard dry 16 – 18 hours at 25 degrees.
- Recoating time: 18 hours.
- New Surfaces must be sound, clean and dry (moisture content below 15%) before priming.
- Ensure to prime the end grain to avoid moisture penetration.
- Previously varnished surfaces.
- For surfaces in poor condition: Strip down and patch prime.
- Surfaces in good condition do not require priming.
- Keep containers properly sealed.
- Store away from direct heat, sun and severe cold.
- 1 Liter – 5 Litres – 20 Litres.
- Detailed safety information: refers to the material safety data sheet for this product.
- Not suitable on sealed or varnished surfaces.
- Do not apply on wet or damp surfaces.
- Do not paint in wet or cold weather. (Minimum 5ºC.)
- Drying times will be extended during wet or cold weather conditions.
PINK WOOD PRIMER
- A solvent based penetrating wood primer for interior and exterior surfaces.
- A general purpose primer for wood
- Economical and easy to apply.
- Good adhesion.
- Very good protection.
- Type: Alkyd.
- Appearance: Matt/low sheen.
- Colors: White and Pink.
- Solids: 63-64% by mass.
- Specific Gravity: 1.35 – 1.4.
- Viscosity (Sheen Cup): 30 -35 Secs.
- DFT/coat: Min 30µm Max 35µm.
- Flash Point: 35ºC.
- Mixing: Stir well before use.
- Method: Short nap mohair roller or brush.
- Thinning: Mineral Turpentine.
- Clean up: Mineral Turpentine.
- Spreading rate: 8 – 10m ²/l depending on surface porosity and profile.
- Conditions: Avoid painting in wet or cold weather. Minimum temp 8º C
- Drying time: Touch dry 3 – 4 hours. Hard dry 16 – 18 hours at 25 degrees.
- Recoating time: 18 hours.
- New Surfaces must be sound, clean and dry (moisture content below 15%) before priming.
- Ensure to prime the end grain to avoid moisture penetration.
- Previously varnished surfaces.
- For surfaces in poor condition: Strip down and patch prime.
- Surfaces in good condition do not require priming.
- Keep containers properly sealed.
- Store away from direct heat, sun and severe cold.
- 1 Liter – 5 Litres – 20 Litres.
- Detailed safety information: refers to the material safety data sheet for this product.
- Not suitable on sealed or varnished surfaces.
- Do not apply on wet or damp surfaces.
- Do not paint in wet or cold weather. (Minimum 5ºC.)
- Drying times will be extended during wet or cold weather conditions.
Experience the difference for yourself.
Transform your space today with our high-quality, premium paints and expert services. Elevate your walls to a level of sophistication that will leave a lasting impression. Contact Versus Paint now and experience the difference for yourself. Let’s create a masterpiece together.
Talk to us
011 885 3136
Send us email
info@versuspaint.co.za
Trust Versus Paint to bring sophistication and style to every brush stroke.
Everything we do is done with a sense of purpose and passion. We know what it takes to make a statement, and we do it with flair.
Join us in the world of luxury, where only the best will do. Choose Versus Paint and experience the Lux Life in all its glory.